manual: document usage of DRTIO switching. Closes #1156

This commit is contained in:
Sebastien Bourdeauducq 2018-11-26 17:53:28 +08:00
parent 0507101e31
commit 5c162ed5e6
3 changed files with 73 additions and 2 deletions

View File

@ -22,12 +22,72 @@ The lower layers of DRTIO are similar to White Rabbit, with the following main d
From ARTIQ kernels, DRTIO channels are used in the same way as local RTIO channels. From ARTIQ kernels, DRTIO channels are used in the same way as local RTIO channels.
.. _using-drtio:
Using DRTIO Using DRTIO
----------- -----------
Remote RTIO channels are accessed in the same was as local ones. Bits 16-24 of the RTIO channel number are used to select between local RTIO channels or one of the connected DRTIO satellites. Bits 0-15 of the RTIO channel number select the channel within one device (local or remote). Terminology
+++++++++++
This scheme will be expanded later with the introduction of DRTIO switches. In a system of interconnected DRTIO devices, each RTIO core (driving RTIO PHYs; for example a RTIO core would connect to a large bank of TTL signals) is assigned a number and is called a *destination*. One DRTIO device normally contains one RTIO core.
On one DRTIO device, the immediate path that a RTIO request must take is called a *hop*: the request can be sent to the local RTIO core, or to another device downstream. Each possible hop is assigned a number. Hop 0 is normally the local RTIO core, and hops 1 and above correspond to the respective downstream ports of the device.
DRTIO devices are arranged in a tree topology, with the core device at the root. For each device, its distance from the root (in number of devices that are crossed) is called its *rank*. The root has rank 0, the devices immediately connected to it have rank 1, and so on.
The routing table
+++++++++++++++++
The routing table defines, for each destination, the list of hops ("route") that must be taken from the root in order to reach it.
It is stored in a binary format that can be manipulated with the :ref:`artiq_route utility <routing-table-tool>`. The binary file is then programmed into the flash storage of the core device under the ``routing_table`` key. It is automatically distributed to downstream devices when the connections are established. Modifying the routing table requires rebooting the core device for the new table to be taken into account.
All routes must end with the local RTIO core of the last device (0).
The local RTIO core of the core device is a destination like any other, and it needs to be explicitly part of the routing table for kernels to be able to access it.
If no routing table is programmed, the core device takes a default routing table for a star topology (i.e. with no devices of rank 2 or above), with destination 0 being the core device's local RTIO core and destinations 1 and above corresponding to devices on the respective downstream ports.
Here is an example of creating and programming a routing table for a chain of 3 devices: ::
# create an empty routing table
$ artiq_route rt.bin init
# set destination 0 to the local RTIO core
$ artiq_route rt.bin set 0 0
# for destination 1, first use hop 1 (the first downstream port)
# then use the local RTIO core of that second device.
$ artiq_route rt.bin set 1 1 0
# for destination 2, use hop 1 and reach the second device as
# before, then use hop 1 on that device to reach the third
# device, and finally use the local RTIO core (hop 0) of the
# third device.
$ artiq_route rt.bin set 2 1 1 0
$ artiq_route rt.bin show
0: 0
1: 1 0
2: 1 1 0
$ artiq_coremgmt config write -f routing_table rt.bin
Addressing distributed RTIO cores from kernels
++++++++++++++++++++++++++++++++++++++++++++++
Remote RTIO channels are accessed in the same was as local ones. Bits 16-24 of the RTIO channel number define the destination. Bits 0-15 of the RTIO channel number select the channel within the destination.
Link establishment
++++++++++++++++++
After devices have booted, it takes several seconds for all links in a DRTIO system to become established (especially with the long locking times of low-bandwidth PLLs that are used for jitter reduction purposes). Kernels should not attempt to access destinations until all required links are up (when this happens, the ``RTIODestinationUnreachable`` exception is raised). ARTIQ provides the method :meth:`~artiq.coredevice.core.Core.get_rtio_destination_status` that determines whether a destination can be reached. We recommend calling it in a loop in your startup kernel for each important destination, to delay startup until they all can be reached.
Latency
+++++++
Each hop increases the RTIO latency of a destination by a significant amount; that latency is however constant and can be compensated for in kernels. To limit latency in a system, fully utilize the downstream ports of devices to reduce the depth of the tree, instead of creating chains.
Internal details Internal details
---------------- ----------------

View File

@ -160,6 +160,8 @@ Configuring the core device
This should be done after either installation method (conda or source). This should be done after either installation method (conda or source).
* (optional) If you are using DRTIO and the default routing table (for a star topology) is not suitable to your needs, prepare the routing table and add it to the ``flash_storage.img`` created in the next step. The routing table can be easily changed later, so you can skip this step if you are just getting started and only want to test local channels. See :ref:`Using DRTIO <using-drtio>`.
.. _flash-mac-ip-addr: .. _flash-mac-ip-addr:
* Set the MAC and IP address in the :ref:`core device configuration flash storage <core-device-flash-storage>` (see above for the ``-t`` and ``-m`` options to ``artiq_flash`` that may be required): :: * Set the MAC and IP address in the :ref:`core device configuration flash storage <core-device-flash-storage>` (see above for the ``-t`` and ``-m`` options to ``artiq_flash`` that may be required): ::

View File

@ -179,6 +179,15 @@ Core device RTIO analyzer tool
.. note:: .. note::
The RTIO analyzer does not support SAWG. The RTIO analyzer does not support SAWG.
.. _routing-table-tool:
DRTIO routing table manipulation tool
-------------------------------------
.. argparse::
:ref: artiq.frontend.artiq_route.get_argparser
:prog: artiq_route
Data to InfluxDB bridge Data to InfluxDB bridge
----------------------- -----------------------